V
主页
IPM电机设计(8.4)安培定理的计算(calculation of Ampère's Theorem8.4)
发布人
打开封面
下载高清视频
观看高清视频
视频下载器
IPM电机设计(8.6)永磁体工作点的计算(calculation of magnet working point8.6)
IPM电机设计(23.1)Maxwell电机DQ轴电感的计算(Calculation of DQ inductance)
空心杯绕组3D模型及其资料
IPM电机设计(8.5)BH曲线的计算(calculation of BH carve8.5)
IPM电机设计(21)Maxwell电机转矩map的计算(Calculation of torque map)
电机中的损耗(2)铜耗的计算
电机中的损耗(1)主要损耗的计算
IPM电机设计(7.1)反电动势的计算(calculation of back EMF7.1)
IPM电机设计(18.3)Maxwell电机电负荷的计算3设置电流激励(Calculation of the Electrical loading)
IPM电机设计(5.3)电磁负荷计算(calculation of electrical loading and magnetic loading5.3)
Maxwell+matlab联合仿真(5)simplorer+SVPWM矢量控制模型1、目前还有问题
IPM电机设计(23.2)Maxwell电机DQ轴磁链的计算(Calculation of DQ flux linkage)
IPM电机设计(7.2)绕组匝数的计算(calculation of turns7.2)
基于ANSYS Electronics(maxwell)的轴向磁通电机设计(盘式电机)(8)实例1三维模型仿真
基于ANSYS Electronics的轴向磁通电机设计(1)基本参数的确定
IPM电机设计(7.5)定子槽高和槽宽的计算(calculation of stator slot dimension7.5)
IPM电机设计(18.2)Maxwell电机电负荷的计算2(Calculation of the Electrical loading)
Motor-CAD资料及其应用指南
基于ANSYS Electronics(maxwell)的轴向磁通电机设计(盘式电机)(7)实例1参数计算及磁路建模
IPM电机设计(14.1)Maxwell转子参数化建模-建立相对坐标系(draw a rotor core)
IPM电机设计(14.2)Maxwell转子参数化建模-建立永磁体槽(draw a rotor core)
Maxwell永磁体退磁仿真设置(1)永磁体材料特性
IPM电机设计(6.5)定子齿部磁通的计算(calculation of stator tooth flux6.5)
IPM电机设计(25)Maxwell电机凸极比计算( Calculation of saliency ratio and output torque)
IPM电机设计(6.7)定子轭部宽度的计算(calculation of width of stator yoke 6.7)
IPM电机设计(20)Maxwell电机静力矩的计算(calcultion of static torque)
IPM电机设计(9.1)卡特系数的计算(calculation of carters coefficient9.1)
基于Maxwell内置GA遗传算法的2维IPM电机模型参数建模优化
IPM电机设计(7.3)定子槽面积的计算(calculation of stator slot area67.3)
IPM电机设计(4.2)电压和电流计算(calculation of voltage and current4.2)
空心杯电机仿真模型和资料
IPM电机设计(13.6)Maxwell定子绕组参数化建模(draw a stator winding)
IPM电机设计(5.4)关键尺寸计算(calculation of main dimensions5.4)
IPM电机设计(7.4)单根导体计算面积(calculation of copper area of singer conductor7.4)
基于ANSYS Electronics(maxwell)的轴向磁通电机设计(盘式电机)(3)前处理设置2
磁场调制型磁齿轮动态性能分析
IPM电机设计(15.4)Maxwell电机零部件材料设置-用记录脚本设置永磁体充磁方向(set direction of magnetization)
IPM电机设计(15.5)Maxwell电机零部件材料设置-用记录脚本设置永磁体充磁方向2(set direction of magnetization)
直线电机设计(2)3D建模练习
Maxwell+matlab联合仿真(4)Maxwell添加simplorer激励、电流源、电压源、pwm波